Edimax-technology AR-7211B Uživatelský manuál

9 CHAPTER II: HARDWARE SETUP 1. Connect the “Line” port of the router and the “Modem” port of the splitter with a telephone (RJ-11) cable. 2. C

10 CHAPTER III: WEB CONFIGURATION 3-1 Connecting to broadband router via web browser You can access the broadband router’s web-based configuration i

11 3. Please input “admin” in the “User name” field and “1234” in the “Password” field. Click the “OK” button to enter the web configuration interfac

12 3-2 Status Click “Status” in the menu to open the sub-menu that contains 5 items: System, LAN, WAN, Statistic, and ARP Table. 3-2-1 System Click

13 3-2-2 LAN Click “LAN” in the sub-menu to open the following screen. In this page, you can view the LAN IP, DHCP Server status, MAC Address and DHC

14 3-2-3 WAN Click “WAN” in the sub-menu to open the following screen. In this page, you can view basic status of WAN, Default Gateway, and DNS Serve

15 3-2-4 Statistics Click “Statistics” in the sub-menu to open the menu in the left bar that contains two items: Traffic Statistics and DSL Statistic

16 3-2-4-2 DSL Statistics Click “DSL Statistics” in the left bar to open the following screen. In this page, you can view the ADSL line statistics, d

17 3-2-5 ARP Table Click “ARP Table” in the sub-menu to open the following screen. In this page, you can view the table that shows a list of learned

18 3-3 Wizard The setup wizard enables speedy and accurate configuration of your Internet connection and other important parameters. The following se

1 COPYRIGHT Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed,

19 Then press Next, the Fig 3.3.1-2 screen will appear. In this page, you can select the WAN Connect Type and the encapsulation method. Fig 3.3.1-2

20 3-4 Network \ LAN Click LAN in the menu to open the sub-menu which contains 2 items: LAN Settings and DHCP Settings. You can use the LAN configura

21 The following table describes the fields of this screen. Label Description IP Address Input the IP of Local area network interface here. Subnet Ma

22 If you set to DHCP Proxy, the screen of Fig 3.4.2-2 appears. Fig 3.4.2-2 The following table describes the fields of this screen. Label Descrip

23 If you set to DHCP Server, the screen of Fig3.4.2-3 appears as shown next. Fig 3.4.2-3 The following table describes the fields in this screen.

24 Click Show Client, the following window appears. In this window, you can view the IP address assigned to each DHCP client. Fig 3.4.2-4 The foll

25 Click MAC-Base Assignment button, the below window appears. In this page, you can assign IP addresses on the LAN to specific individual computers b

26 3-5 Network \ WAN Click WAN Interface in the menu to open the sub-menu which contains 3 items: WAN Interface, ATM Settings and ADSL Settings. 3-5

27 points in an ATM network, and its valid value is from 0 to 255 VCI The virtual channel between two points in an ATM network, ranging from 32 to 655

28 VC Table. Modify Select a PVC in the Current ATM VC Table, then modify the parameters of this PVC. When you finish, click this button to apply the

2 CONTENTS CHAPTER I: INTRODUCTION ...

29 3-5-3 ADSL Settings Click ADSL Interface in the sub-menu to open the screen of Fig 3.5.2. In this page, you can select the DSL modulation. Mostly,

30 3-6 Service & Advance Click Advance in the menu to open the sub-menu which contains 6 items: DNS, Firewall, Virtual Server, Routing, IP QOS, a

31 Label Description Attain DNS Automatically When this checkbox is selected, this router will accept the first received DNS assignment from one of th

32 3-6-2 Firewall Click Firewall in the sub-menu to open the menu in the left bar, whick contains three items:IP/Port Fileter, MAC Filter and URL Blo

33 3-6-2-2 MAC Filter Click MAC Filter in the left bar to open the screen of Fig 3.6.2.2. Entries in this table are used to restrict certain types of

34 3-6-2-3 URL Blocking Click URL Blocking in the left bar to open the screen of Fig 3.6.2.3. This page is used to configure the Blocked FQDN(Such as

35 3-6-3 Firewall – II Click Virtual Server in the sub-menu to open the menu in the left bar,whick contains two items:Services and DMZ Settings. 3

36 3-6-3-2 DMZ Settings Click DMZ Settings in the left bar to open the screen of Fig 3.6.3.2. A Demilitarized Zone is used to provide Internet servic

37 3-6-4 Routing Click Routing in the sub-menu to open the menu in the left bar, whick contains two items: RIP and Static Route. 3-6-4-1 RIP Click

38 3-6-4-2 Static Route Click Static Route in the left bar to open the screen of Fig 3.6.4.2-1. This page is used to configure the routing informatio

3 3-6-6-1 IGMP Proxy ... 40 3-6-6-2 UPN

39 3-6-5 IP QoS Click IP QoS in the sub-menu to open the screen of Fig 3.6.5. Entries in this table are used to assign the precedence for each incomi

40 3-6-6 Service --II Click Others in the sub-menu to open the menu in the left bar,whick contains four items:IGMP Proxy, UPNP, Bridge and IP Pass

41 3-6-6-2 UPNP Click UPNP in the left bar to open the screen of Fig 3.6.6.2. This page is used to configure UPnP. The system acts as a daemon after

42 Click Show MACs button in Fig 3.6.6.3-1, the below window will appear. This table shows a list of learned MAC addresses for this bridge. Fig 3.6.

43 3-6-6-5 SNMP Click SNMP in the sub-menu to open the screen of Fig 3.7.7. In this page, you can set the SNMP parameters. Fig 3.7.7 Label Descrip

44 3-6-6-6 Service \ TR069 Click TR069 in the sub-menu to open the screen of Fig 3.7.8. In this page, you can configure the TR-069 CPE. Fig 3.7.8

45 3-6-6-7 Service \ ACL Click ACL in the sub-menu to open the screen of Fig 3.7.9. In this page, you can configure the IP Address for Access Control

46 3-7 Admin Click Admin in the menu to open the sub-menu which contains 9 items: Remote Access, Commit/Reboot, Password, Backup/Restore, Upgrade Fir

47 3-7-2 Password Click Password in the sub-menu to open the screen of Fig 3.7.3. In this page, you can change the password of the user, include admi

48 3-7-3 Backup/Restore Click Backup/Restore in the sub-menu to open the screen of Fig 3.7.4. In this page, you can backup the current settings to a

4 CHAPTER I: INTRODUCTION Thank you for purchasing this Edimax product. This router is a cost-effective router, an ADSL2+ modem, and Ethernet network

49 3-7-4 Firmware Upgrade Click Upgrade Firmware in the sub-menu to open the screen of Fig 3.7.5. In this page, you can upgrade the firmware of this

50 3-7-5 Time Zone Click Time Zone in the sub-menu to open the screen of Fig 3.7.6. In this page, you can set the system time manually or get the syst

51 3-8 Diagnostic Click Diagnostic in the menu to open the sub-menu which contains 4 items: Ping, ATM Loopback, ADSL and Diagnostic. 3-8-1 Ping Cli

52 3-8-2 ATM Loopback Click ATM Loopback in the sub-menu to open the screen of Fig 3.8.2. In this page, you can use VCC loopback function to check th

53 Fig 3.8.3 Start: Click this button to begin ADSL Tone Diagnostics. 3-8-4 Diagnostic Click Diagnostic in the sub-menu to open the screen of Fig

54 APPENDIX A: USB SOFTWARE SETUP Execute Setup.exe to startup InstallShield Wizard, Fig A-1 will be shown: Fig A-1 Then press Next, the Fig A-2 s

55 After Setup finished, Fig A-3 will be shown:connect or disconnect your ADSL MODEM to PC as follow prompt. Fig A-3 Before install driver program.

56 Select “No, not this time” and press “Next”, Fig A-5 will be shown below: Fig A-5

57 Select “Install the software automatically (Recommended)” and then press “Next” button, Windows will search and find the USB driver and automatical

58 Fig A-7

5

59 APPENDIX B: ABBREVIATIONS ADSL Asymmetric Digital Subscriber Line ATM Asynchronous Transfer Mode ATU C ATU at the central office end (i.e

60

6 1-1 Package Contents  One single port router  One external splitter  One power adapter  Two pieces of telephone lines(RJ-11,more than 1.8m)

7 1-3 LED and Interface Description Front Panel LED Color Status Description Power Green/ Red OFF Device not powered GREEN Device correctly power

8 Rear Panel Item Usage Line Line RJ-11 port Reset Resets device to factory defaults (to restore factory defaults, push a paper clip into the ho