Edimax-technology AR-7167WnB Uživatelský manuál

6 2. Hardware Installation Step 1. Connect the ADSL Line Connect the router to your ADSL cable through the supplied RJ-11 telephone line. Step 2.

7 3. IP Address Setting Using the router to get into the Internet, the PCs in the network must have Ethernet adapter installed and be connected to

8 4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select Obtain an IP address automatically and Obtain DNS server address autom

9 Windows Vista 1. Click the Start button and select Settings and then select Control Panel. Double click Network and Sharing Center, the Network

10 5. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your router‟s DHCP server. Note: Please make sure

11 Windows XP 1. Click the Start button and select Control Panel and then double click Network Connections. The Network Connections window will ap

12 5. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your router‟s DHCP server. Note: Please make sure

13 4. Web Management Configuration Once you have configured your PCs to obtain an IP address automatically, the router‟s DHCP server will automatic

14 4.1. Quick Start The Quick Start section is designed to get you using the router as quickly as possible. Before configuring the router, please c

15 Please follow the steps in the setup wizard to complete the configuration of the Internet connection. Step 1: Set your new password Please en

Copyright by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in

16 Step 2: Choose your tome zone Please select the tome zone where you are located. Step 3: Set your Internet connection Please check with your

17 Step 4: Input the data supplied by your ISP To know more about the explanation of each setting, please refer to Section 4.2. Step 5: Re-start

18 4.2. General Setup Please start your web browser and log onto the web management interface of the router, then click „General Setup‟ button on

19  ATM VC Parameter Description Virtual Circuit VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier define a virtual circuit. Sta

20 nrtVBR (non-real time Variable Bit Rate) – This class allows users to send traffic at a rate that varies with time depending on the availability

21  Dynamic IP Address Parameter Description Encapsulation Please check with your ISP the method of multiplexing. In Bridge Mode, please select

22 IP addresses for internal traffic and a second set of addresses for external traffic. When NAT is enabled, the router will help to make all neces

23  Static IP Address Parameter Description Encapsulation Please check with your ISP the method of multiplexing. In Static IP Mode, please selec

24 Static IP Address Enter the IP Address assigned by your ISP. IP Subnet Mask Enter the Subnet Mask assigned by your ISP. Gateway Enter the Gat

25  PPPoE/PPPoA Parameter Description User Name Enter the username exactly as your ISP assigned. Password Enter the password that your ISP ha

Contents 1. INTRODUCTION ... 1 1.1. FEATURES ...

26 Connection Always On – The connection will be kept always on. If the connection is interrupted, the router will re-connect automatically. Con

27 chose Static above. Gateway Enter the Gateway assigned by your ISP. Only if you chose Static above. NAT NAT (Network Address Translation), an

28  Bridge Mode Parameter Description Encapsulation Please check with your ISP the method of multiplexing. In Bridge Mode, please select “1483 B

29  LAN Settings Parameter Description IP Address Enter the IP Address of the ADSL router for the local user to access the router‟s web page. By

30 dynamic routing. After the RIP protocol is selected, please choose the RIP direction from “None”, “Both”, “IN Only” or “OUT Only”. DHCP Select

31 Secondary DNS This is optional. You can enter another DNS Server‟s IP Address as a backup. The secondary DNS will be used should the Primary DNS

32 Beacon Interval The interval of time that this wireless router broadcast a beacon. Beacon is used to synchronize the wireless network. The rang

33 rate 54Mbps for 802.11g clients, and maximum 150Mbps for 802.11n clients). 802.11b+g+n – It allows 802.11b, 802.11g, and 802.11n wireless networ

34 efficiency. Select 400nsec to provide a shorter delay between transmission frames in 11n network. The throughput in 400nec guard interval is bet

35  WPS Settings Wi-Fi Protected Setup (WPS) is the simplest way to build connection between wireless network clients and this router. You don‟

4.2.3.4.2. Application Filter ... 53 4.2

36 Authentication Type It‟s very important to set wireless security settings properly. If you don‟t, hackers and malicious users can reach your netw

37 WPA-PSK/ WPA2-PSK When “WPA-PSK/WPA2-PSK” is selected, please select the encryption method (TKIP or AES) and enter 8-63 ASCII characters or 64 he

38 4.2.2. Advanced Setup 4.2.2.1. Firewall Parameter Description Firewall When you enable the firewall function, it will protect you from fol

39  Routing Table List You can see the current routing table of the router here. If you want to add another routing rule, please click “ADD ROUTE

40 Parameter Description Destination IP Address Enter the IP Address of the destination LAN. IP Subnet Mask Enter the Subnet Mask address of t

41 4.2.2.3.1. NAT Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Addr

42 DMZ Host IP Address Enter a static IP Address to the DMZ Host. This IP Address will be exposed to the Internet. 4.2.2.3.3. Virtual Server Use

43 Local IP Address It is recommended to enter a static IP Address for the server here. If the server‟s IP Address is obtained from DHCP Server, the

44  Quality of Service Parameter Description QoS QoS can be toggled Activated and Deactivated. QoS must be activated before you can edit the foll

45 different rules, each rule can be activated or deactivated. Application Select 11 different applications: There are IGMP, SIP, H.323, MGCP, SNM

1 1. Introduction The AR-7167WnA/B provides four 10/100 base-T Ethernet ports for user. The device provides high-speed ADSL2+ broadba

46 IPP/DS Field Select IP QoS format. IP Precedence Range Select the IP precedence range. Type of Service Select 5 different type of service.

47 4.2.3. Access Management 4.2.3.1. UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Window

48  Dynamic DNS Parameter Description Dynamic DNS Activated or deactivated the DDNS function. Service Provider This router supports DynDNS se

49 your LAN or WAN. You can control which computer can have access to these services by entering the IP Address of the computer.  ACL Parameter

50 Application Choose the services that you permit to use in your LAN or WAN interface. These services include Web, FTP, Telnet, SNMP and Ping.

51 4.2.3.4.1. IP/MAC Filter  Rule Type Parameter Description Rule Type Selection Select the rule type of type of filter.  IP / MAC Filter R

52 Interface Select which channel (PVC) to configure. Direction Select the access to the Internet (Outgoing) or from the Internet (Incoming), or B

53 4.2.3.4.2. Application Filter  Application Filter Editing Parameter Description Application Filter Activate or deactivate the application

54  URL Filter Editing Parameter Description Active Activate or deactivate the URL filter. URL Index This is the item number to record the setti

55 4.3. Status The status screens give you information about various aspects of your ADSL router’s settings. 4.3.1. Device Info In this page,

2 1.1. Features ADSL2/2+ Compliance  Support downstream rates of up to 24Mbps and upstream rates of up to 1Mbps.  Compliant to ITU-T G.992.1 (G

56 4.3.2. System Log Display system logs accumulated up to the present time. You can also save the logs for future reviewing.

57 4.3.3. Statistics Show the statistics of transmit and receive packets on the LAN port, ADSL line or WLAN port.

58 4.4. Tools 4.4.1. Administrator Parameter Description Username The username of the router is “admin” by default. New Password Enter up

59 4.4.2. Time Zone The Time Zone allows your router to set its time; this will affect function such as System Log. Parameter Description Curren

60 4.4.3. Firmware If you have new firmware for some features update, please upgrade firmware of the router here. Parameter Description New Firm

61 4.4.4. System Restart In this page, you can restart your router or restore to factory defaults. If you wish to restart the router using the fa

62 FFeeddeerraall CCoommmmuunniiccaattiioonn CCoommmmiissssiioonn IInntteerrffeerreennccee SSttaatteemmeenntt This equipment has been tested

63 The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Ital

64

3 Access Management  ACL (Access Control)  IP/MAC/Application/URL Filter  UPnP (Universal Plug and Play)  Dynamic DNS 1.2. Minimum Requir

4 1.4. Hardware Placement 1.4.1. Rear Panel Item Name Description Antenna The 3dBi dipole antennas. Radio ON/OFF Switch the button to activate o

5 1.4.2. Front LEDs On the router‟s front panel there are LED lights that inform you of the router‟s current status. Below is an explanation of eac